Loxeal
Loxeal Engineering Adhesives is an Italian Company Specialized in the manufacturing of comprehensive range of Technically Advanced Adhesives and Sealants providing since over 35 years solutions to a wide variety of industrial uses
LIGHT CURING ADHESIVE
UV light curable adhesives polymerise in seconds by irradiation with UV and visible light, forming a solid adhesive film not yellowing over time. Designed to bond glass, crystal, metals and some plastics. Operating temperature range between -50°C and +120°C. A non-drip gel formulation is available for vertical applications.
UV30-20: UV light cure adhesive for glass and crystal
UV30-21: High strength UV adhesive for glass and metal
UV30-23: Low viscosity UV adhesive for glass and crystal
EPOXY ADHESIVES
Two-part engineering adhesives provide high strength, structural joints. They are suitable for bonding metals, ceramics, wood and some plastics and they are supplied in a practical dual cartridge dispenser. Curing occurs upon mixing of the two components (resin and hardener). Fixture time is from 5-10 minutes to several hours. Applying heat will accelerate the cure speed. Temperature resistance is between -30°C and +80°C, +120°C for some products. Available in dual cartridges with static mixer.
EPOXY ADHESIVES
Two-part engineering adhesives provide high strength, structural joints. They are suitable for bonding metals, ceramics, wood and some plastics and they are supplied in a practical dual cartridge dispenser. Curing occurs upon mixing of the two components (resin and hardener). Fixture time is from 5-10 minutes to several hours. Applying heat will accelerate the cure speed. Temperature resistance is between -30°C and +80°C, +120°C for some products. Available in dual cartridges with static mixer.
THREADSEALING
Anaerobic threadsealing adhesives seal and lock threaded connections against pressure of gas, air, water, oils, hydrocarbons and many chemicals. They replace hemp and PTFE tapes and are available in various grades of locking strength with resistance to various chemicals. Certified according to various international standards, e.g. DVGW, NSF, WRAS, KTW, BAM, WATER MARK.
THREADLOCKING
Anaerobic threadlockers lock studs, nuts, screws and any threaded fasteners. The adhesive prevents loosening caused by vibration, mechanical and thermal shock. Threadlocking adhesive also inhibits fretting corrosion and prevents the seizure and galling.
THREADLOCKING
Anaerobic threadlockers lock studs, nuts, screws and any threaded fasteners. The adhesive prevents loosening caused by vibration, mechanical and thermal shock. Threadlocking adhesive also inhibits fretting corrosion and prevents the seizure and galling.
LIQUID GASKETING
Gasketing anaerobic adhesive seals flat mating surfaces and joins flanges on pumps, gearboxes and differential housings. It replaces preformed gaskets and allows contact between metal parts forming a seal which is not prone to creep or relaxation. It forms a flexible and / or elastic gasket resistant to vibration, heat, oil and other industrial fluids. Parts can be disassembled using normal tools.
RETAINING
Retaining anaerobic adhesives lock and fit bushes, bearings, sleeves, pin hubs, pulleys, gears and other cylindrical components. They are ideal for increasing the strength of press fit parts or retaining loose fitting parts, allow larger machining tolerances, reducing manufacturing costs, prevent fretting corrosion, vibration loosening and distortion. Retaining adhesives have excellent chemical resistance and seal against most fluids.
RETAINING
Retaining anaerobic adhesives lock and fit bushes, bearings, sleeves, pin hubs, pulleys, gears and other cylindrical components. They are ideal for increasing the strength of press fit parts or retaining loose fitting parts, allow larger machining tolerances, reducing manufacturing costs, prevent fretting corrosion, vibration loosening and distortion. Retaining adhesives have excellent chemical resistance and seal against most fluids.
INSTANT ADHESIVES
Cyanacrylate adhesives are for instant and structural bonding of rubber, metals, ceramic, leather and a variety of plastics. Best results can be obtained with joint gaps of less than 0.1mm up to 0.2mm for special grades.
The service temperature range is between -50°C and +80°C, although new high-temperature resistant formulations are available for use up to 180°C. For porous surfaces or for vertical application a gel grade is available.